Epoxy coating with photoluminescent pigment EN 100
Epoxy coating with photoluminescent pigment EN 100
This epoxy resin with photoluminescent pigment is one of the highest quality lamination systems, thanks to the use of the highest quality raw materials on the market. The set is primarily intended for painting, but it can also be used for casting up to a thickness of 4 mm / 30 g. Instructions are given on the product packaging More
Manufacturer: Traiva s.r.o Product code: P00044 Shipping and Payment
23,07 € excl. VAT (27,91 € incl. VAT)
This epoxy resin with photoluminescent pigment is one of the highest quality lamination systems, thanks to the use of the highest quality raw materials on the market. The set is primarily intended for painting, but it can also be used for casting up to a thickness of 4 mm / 30 g. Instructions are given on the product packaging More
Manufacturer: Traiva s.r.o Product code: P00044 Shipping and Payment
Variants2
The epoxy resin in the set with hardener and photoluminescent pigment contains a resin weighing 500 g (+ 150 g hardener and 150 g pigment), or 1000 g (+300 g hardener and 300 g pigment). In the menu you can choose between light green-yellow or blue pigment.
The cured resin with a light green-yellow pigment, when illuminated in the dark, glows bright greenish light. In the case of a resin with a blue pigment, it shines with a bright turquoise color. The cured resin glows up to 2000 mcd / m2 after 1 minute and 2500 mcd / m2 after 10 minutes of illumination. It lasts for about 12 hours.
The epoxy system EP100 with a new hardener was developed based on your requirements, a UV stable and high glowing in the dark product. The system exhibits extreme transparency and minimal shrinkage. It is very friendly to the environment and your health, because almost no harmful fumes were measured during curing. It does not cause an allergic skin reaction under normal use.
The new hardener significantly suppresses oxidation and subsequent yellowing of the laminate. This new system is one of the highest quality lamination systems, thanks to the use of the highest quality raw materials on the market. The set is primarily intended for painting, but it can also be used for casting up to a thickness of 4 mm / 30 g. Instructions are given on the product packaging.
Technical description
Mixing ratio: up to 100 g resin 30 g pigment and 30 g hardener. The usability after mixing the hardener is about 50 minutes before the resin begins to solidify. Add the pigment to the resin gradually in small portions. Stir the mixture thoroughly until air bubbles are removed. Then add the hardener and mix thoroughly again. Resin application is possible with a brush or roller. Instructions on the product packaging.
Weight 800 g contains:
- resin - 500 g
- hardener - 150 g
- pigment - 150 g
Weight 1600 g contains:
- resin - 1000 g
- hardener - 300 g
- pigment - 300 g
Download
Related products6
BISON GRIZZLY MONTAGE EXTREME 440g, mounting adhesive with immediate fixation
7,96 € incl. VAT
Holders for escape route marking
from 4,36 € incl. VAT
Double-sided adhesive nano tape - transparent, Signus HP38, 3 m
from 3,56 € incl. VAT
Alternative products5
Epoxy resin crystal clear for casting EZ 350
31,96 € incl. VAT
Epoxy resin with photoluminescent pigment for casting EZ 350
42,73 € incl. VAT
Epoxy resin Veropal ClearCast 300, for casting layers up to 5 cm
from 27,16 € incl. VAT
Epoxy resin Veropal UV Plus 100, for casting layers up to 10 cm
from 45,56 € incl. VAT